Hydraulic cap Study guides, Class notes & Summaries

Basic Vehicle Rescue Technician Proboard Exam - Questions and Answers If your community has rail service, it is very important to: Conduct thorough pre-incident planning and respond with normal incident expectations A disadvantage of a ratchet jack is: failure under heavy loads The most common size cribbing is: 4" X 4" Cribbing Medium trucks (Classes 3, 4, 5) have a gross vehicle weight rating (GVWR) between: 5,000 lbs to 15,000 lbs All of the following should be done to stabilize an upright...

Maine State Inspection Administrative Test Already Passed AGENT the owner or representative of a Sticker Replacement Station or Window Tint Station who is licensed according to this Chapter. CRITICAL VISION AREA that area of the windshield covered by the normal sweep of all except the lower 4 inches of properly adjusted wiper blades, utilizing factory installed blades or equivalent replacements. FLEET INSPECTION STATION a non-public inspection station licensed to perform inspecti...

Intermediate Hydraulics Study Guide Questions & Answers Hydraulic 4/2 DCVs are often used as 3/2 DCVs by______. a. Changing the spool b. Blocking a port c. Placing the spring on the other end d. Changing the operator - Correct Ans-Blocking a port The spool of the pilot valve controlling a 4/3 pilot-operated DCV is always a(n)_______. a. Closed center b. Open center c. Float center d. Tandem center - Correct Ans-Float center The circuit that controls fast approach, followed by a decrea...

BECC MOD 7 When starting up the Hydraulic System, the ....... must be used. - correct answer EOSS Hydraulic systems are used to operate the ....... - correct answer STEERING GEAR If you apply 100 pounds of force to a 1 inch piston, the 2 inch output piston would have ....... pounds of force. - correct answer 200 Hydraulic system pressure is maintained by the ....... valve - correct answer UNLOADING Which component is used to convert fluid power energy to mechanical motion? - correct...

BECC MOD 7 QUESTIONS AND ANSWERS WITH CERTIFED SOLUTIONS When starting up the Hydraulic System, the ....... must be used. EOSS Hydraulic systems are used to operate the ....... STEERING GEAR If you apply 100 pounds of force to a 1 inch piston, the 2 inch output piston would have ....... pounds of force. 200 Hydraulic system pressure is maintained by the ....... valve UNLOADING Which component is used to convert fluid power energy to mechanical motion? ACTUATOR The centrifugal type LP ai...

What does AAV stand for? - Answer-An allowable alternative vehicle as defined 29-A MRSA 2301 Who/What is an Agent? - Answer-The owner or representative of a Sticker Replacement Station or Window Tint Station who is licensed What is an Autocycle? - Answer-An enclosed motorcycle, originally manufactured as an autocycle. It is designed to have no more than three wheels in contact with the ground at any time. What is a Bumper Protection System? - Answer-The protective design feature(s) of a veh...

Torches are designed to avoid mixing oxygen and acetylene by using __________. - Answer Reverse-flow check valves at torch inlets or regulator outlets To prevent leakage around the valve during use, __________ - Answer An oxygen cylinder valve should be opened all the way An explosion can occur if __________ comes in contact with oil. - Answer High pressure oxygen A green welding hose normally indicates that this hose carries __________. - Answer Oxygen A __________ is a non-destruct...

The three main components of a hydraulic power unit Hydraulic Pump Reservoir Prime Mover Hydraulic Pump Supplies oil from the reservoir to the system Components A part of a larger ,interacting system Reservoir Stores the oil, while also allowing it to cool and settle out dirt. It also provides a convenient location to mount other hydraulic components Schematic symbol of a reservoir Prime Mover Provides the energy to cause the main shaft of the pump to ro...

Mechatronics Midterm Midterm exam review for ADMF 222 Questions & Answers 2023 1. The DCV spool that connects all ports in the center position is called __________. - Correct Ansopen 2. A cam-operated 4/2 valve can also be described as a __________. - Correct Ans-roller-operated valve 3. Three-way, 2 position DCVs ( called 3/2 valves) are used to __________. - Correct Ans-Power actuators in one direction 4. A typical application of a hydraulic 4/2 DCV is __________. - Correct Ans-All o...

BECC MOD 7 Study practice exam final Q&A When starting up the Hydraulic System, the ....... must be used. - CORRECT ANSWEREOSS Hydraulic systems are used to operate the ....... - CORRECT ANSWER-STEERING GEAR If you apply 100 pounds of force to a 1 inch piston, the 2 inch output piston would have ....... pounds of force. - CORRECT ANSWER-200 Hydraulic system pressure is maintained by the ....... valve - CORRECT ANSWERUNLOADING Which component is used to convert fluid power energy to ...