Boiler test Study guides, Class notes & Summaries

What is the first thing a tech should do when arriving at a no combustion call? - Answer- Ask how many times the customer reset the unit. What is the best long term solution for preventing a clogged nozzle? - Answer- -Remove any underground storage tanks. -Install a quality oil filter. -Cut the suction line 10" above the tank outlet to prevent sludge. Hot water and steam valves are interchangeable. - Answer- False When in the presence of a flame, a cad cell normally reads.. - Answer...

What must you do if you notice code violations in a homeowners house? - Answer Notify them and recommend ways to address them What must be done when performing an annual tune-up on a heating system? - Answer A combustion efficiency test and a copy must be posted on site Whenever a furnace, direct fired hot water heater, or boiler is installed the total installation must be brought into compliance with what requirements BEFORE appliance can be fired? - Answer NFPA 31 When an eme...

CLASS 5 BOILER TEST

Boilermaker NCCR Test (Latest) Questions With 100% Correct Ans..

Boilermaker NCCR Test Questions And Answers Boilermaker NCCR Test 1 ft 3-3/4 in + 2 ft 1-1/16 in +5 ft 10- 7/8 in = - ANS 9 ft 3-11/16 in A 1-inch plate is to be cut. Why should an acetylene gerulator on a cutting rig not be adjusted over 15 PSI? - ANS Acetylene is unstable above this pressure A big control valve is pulled who is responsible for the rigging? - ANS Crane operator and rigger A boiler maker must have all of the following wh...

Minnesota Special Engineer Boiler License Exam Prep (2023/2024 Update) | Questions and Verified Answers| 100% Correct Q: A feed water line must have what two valves? Answer: Check & stop Q: After a new boiler is installed, what must be performed? Answer: Hydrostatic test Q: All stationary boilers of what pressure must have 2 valves on the blow off line? Answer: 100psi Q: How is boiler efficiency calculated? Answer: Output divided by input Q:...

Nyc high pressure boiler license Exam Questions with Correct Answers The minimum blowdown for a spring loaded safety valve shall be of what percent of set pressure? - Answer-10% How is the main steam pressure gages tested? - Answer-With an inspectors gage Who is in charge of the code for any plumbing installations? - Answer-The nyc plumbing code When will anchorage or guides be inspected? - Answer-Annually How many brass washout plugs does a miniature boiler have? - Answer-3 brass wa...

What is a general requirement of the location of the installation of a boiler? - ANSWERSAdequate clearance from combustile construction What temperature must the materials remain under during combustion? - ANSWERS170 degrees What is a requirement for the access of the boiler? - ANSWERSAccess for operation and maintenance must not be hazardous What is required upon installation to operate a boiler? - ANSWERSInspection and test resulting in equipment use permit from commissioner How of...

Ohio Boiler Test Questions and Answers Graded A+ The pressure at the base of a vertical foot of water is 0.433 psi. When performing a hydrostatic test, the pressure on the boiler should be increased to 1 1⁄2 times the safety valve setting . A boiler steam pressure gauge should have a range of 1 1⁄2 to 2 times the safety valve setting: The maximum size of the bottom blowdown line and the surface blowdown line is 2 1/2" During startup, the boiler vent should remain open unt...

Low pressure boiler practice test Water, heat and container - correct answer Is necessary to generate steam in a boiler Heating surface - correct answer The _____ is the part of the boiler with water on one side and heat on the other Firetube - correct answer A _____ boiler has heat and gases of combustion that pass through tubes surrounded by water Watertube - correct answer A _____ boiler has water in the tubes and heat and gases of combustion passing around the tubes Baffles - co...