Bushing Study guides, Class notes & Summaries

Which of the following is true with regard to switchboards Switchboards are used to subdivide large blocks of power When installing wiring within switchgear, use self adhesive cable ties every ___. 12" (300mm) The maximum voltage that a piece of equipment can withstand is known as its ____. Basic impulse insulation level (BIL) Bolted pressure switches are often used in place of ___. Circuit breakers A transformer's temperature rise rating refers to ___. The maxim...

NETA III 2024 QUESTIONS WITH CORRECT SOLUTIONS The alternate source for emergency systems are required to be equipped with ground-fault protection of equipment. -Answer-False Which ANSI/IEEE standard covers SF6 circuit breakers? -Answer-C37.04 You measure the winding resistance of a 12.4kV, 1000kVA, Delta-Delta connected transformer with a 100A test set. H1-H2 measures 42.0 microhms, H2-H3 measures 41.9 microhms, and H3- H1 measures 84.0 microhms. What can you conclude from these readings...

TEST BANK FOR RADIOLOGIC SCIENCE FOR TECHNOLOGISTS 12TH EDITION BY BUSHING ALL CHAPTERS 1-40 COVERED GRADED A+

Truck Foundations Part 1 new exam questions and answer What type of side frame rails do Ram Light Duty pickups use? Which statement best describes fade resistance? What factors determine braking efficiency? The class-exclusive-Active-Level rear air suspension available on Ram 2500 and 3500 has ___________ ride modes for enhanced load leveling. What standard rear suspension does Ram 3500 have? The suspension travel on the TRX is the longest applied on a full-size Ram pickup...

Which of the following is the proper way to adjust the rack yoke bearing? A. Tighten to 75 ft lbs. B. Tighten to 5 inch lbs. C. Tighten and then back off the original equipment manufacturer's (OEM) specifications. D. Tighten to 0.002" end-play. Tighten and then back off the originial equipment manufacturer's (OEM) specifications. Many OEMs will recommend that the technician tighten to a specification then back off a certain number of degrees. A customer says that the steering whee...

1. The truck with the air suspension system shown above leans to the right. Technician A says that valveX could be the cause. Technician B says that valve Y could be the cause. Who is right? A. Technician A only B. Technician B only C. Both A and B D. Neither A or B - Answer- 1. The correct answer is C, both technicians are right. Height control valves can fail in either direction-that is, by controlling the height at too great a level or at too low a level. If the truck leans, the cause c...

1. The truck with the air suspension system shown above leans to the right. Technician A says that valveX could be the cause. Technician B says that valve Y could be the cause. Who is right? A. Technician A only B. Technician B only C. Both A and B D. Neither A or B - Answer- 1. The correct answer is C, both technicians are right. Height control valves can fail in either direction-that is, by controlling the height at too great a level or at too low a level. If the truck leans, the cause c...

An automotive _____ connects and disconnects the engine and manual transmission or transaxle. - Answer- Clutch. What is the benefit of a wet clutch? - Answer- A wet clutch does not slip, as a fluid coupling or torque converter may, and is more energy efficient. Clutch disc _____ springs help absorb some of the vibration and shock produced by clutch engagement. - Answer- Torsion or damping. What is the main purpose of the pressure plate cover? - Answer- Its main purpose is to hold the pa...

The bushing or bearing that supports the forward end of the transmission input shaft is called the A. Release bearing B. Clutch bearing C. Input bearing D. Pilot bearing - Answer- D. Pilot bearing How is the friction material attached to the clutch disk A. Glued to both sides of the disc B. Riveted to both sides of the disc C. Bolted to the backside of the disk D. Held by springs to the front side of the disk - Answer- B. Riveted to both sides of the disc How is the clutch p...

ASE T5 questions with correct answers 1. The truck with the air suspension system shown above leans to the right. Technician A says that valveX could be the cause. Technician B says that valve Y could be the cause. Who is right? A. Technician A only B. Technician B only C. Both A and B D. Neither A or B - ANS 1. The correct answer is C, both technicians are right. Height control valves can fail in either direction-that is, by controlling the height at too great a level or at too low a...